#WHERE TO PUT EHX MICROSYNTH IN CHAIN FULL#
#WHERE TO PUT EHX MICROSYNTH IN CHAIN FREE#

Please run the Micro Synth off of its own power adapter.Д©V Power Jack вЂ“ Connect the plug from the supplied 9VDC AC Adapter to the 9V power jack. IMPORTANT PLEASE READ: The Micro Synth will not work with the same power adaptor that is daisy chained to other pedals in its signal chain. You can record your new settings in the blank templates provided.

#WHERE TO PUT EHX MICROSYNTH IN CHAIN FREE#

Once youвЂ™ve tried all the sample settings, feel free to experiment to develop your own unique palette of sounds. SOUND TEMPLATES: The sample settings include with these instructions will help you get -familiar with your BASS MICRO SYNTH and its controls.It is recommended that RATE be synchronized with your playing speed. RATE: Determines the speed at which the filter sweeps from START FREQUENCY to STOP FREQUENCY.In addition to lead synthesizer sounds, START and STOP controls can be used to simulate attack, decay, and harmonic content of acoustic instruments. This is also the вЂњresting frequencyвЂќ of the filter, and if the START and STOP controls are set at the same level no sweep will occur, though the filter will provide emphasis of that particular frequency band. STOP FREQUENCY:Determines the frequency at which the filter sweep ends.START FREQUENCY: вЂ“ Determines the frequency at which the filter sweep begins.Higher settings will produce a more emphasized filter sound and also add a slight boost to the signal. RESONANCE:Affects the degree of sharpness, or вЂњQвЂќ of the filter.The final four controls comprise the FILTER SWEEP section. It is recommended that you synchronize your playing to the speed setting of the ATTACK DELAY. Different delay times contribute greatly to the characteristic sounds of various instruments. Higher-numbered settings can completely remove the initial attack of the instrument.

#WHERE TO PUT EHX MICROSYNTH IN CHAIN FULL#

ATTACK DELAYДetermines the time required for the voice signals to reach full volume. In all other respects it operates in a similar fashion to a standard distortion device. Intensity of this voice is also determined by instrument attack or volume. SQUARE WAVE: Controls the output volume of the Square wave.This voice contains a small amount of harmonic distortion for added richness of tone. OCTAVE: Controls the output volume of the Octave.The Sub-Octave effect only tracks single notes. SUB OCTAVE:Controls the output volume of the Sub-Octave.GUITAR: Controls the output volume of the input signal through the filter.Please not the following voice characteristics: Each voice is completely independent and can be mixed with the others in any degree. The next four controls of the BASS MICRO SYNTH comprise the VOICE MIXING section: GUITAR, SUB-OCTAVE (one octave below), OCTAVE (one octave above), and SQUARE WAVE. It is best to set the TRIGGER at exactly the sensitivity needed for your playing. This is especially true if chords are played. If the TRIGGER is set too high, the filter may вЂњstutterвЂќ due to multiple triggering. TRIGGER вЂ“ Determines the input volume at which the filter circuits will вЂњturn on.вЂќ It does not affect any other circuitry. When the Status LED is off, the Bass Micro Synth is in True Bypass mode. When the Status LED is lit, the Bass Micro Synthesizer is in effect mode. In all cases, high-numbered control settings increase the level of the given effect.ДЇOOTSWITCH and Status LED вЂ“ The Footswitch selects either effect mode or True Bypass. OPERATION The Bass Micro SynthвЂ™s controls operate as described below.

Please do not touch any other components when the bottom plate is removed or you risk damaging the circuit board or the components. Turning it counter-clockwise will decrease preamp gain. Turning the trim pot clockwise will increase the preamp gain.

Look for the small trim pot in the lower left corner of the circuit board, it is labeled TRIM1 GAIN TRIM. To access the preamp gain adjustment, remove the bottom plate from the Bass Micro Synth. A screwdriver or alignment tool with a tip width of no more than 1/16вЂі is required. If you will be using another instrument with higher or lower output, it may be necessary to readjust this setting. The preamp gain in the Bass Micro Synth has been set at the factory for use with a bass equipped with single-coil passive pickups. The Micro Synth must have its own power supply. In addition, do not use a daisy chained supply with the Micro Synth. Using the wrong adapter may also damage your unit and will void the warranty. Using the wrong adapter can cause serious bodily injury. WARNING: Your Bass Micro Synth comes equipped with an Electro-Harmonix 9.6DC-200BI power supply (same as used by Bossв„ў & Ibanezв„ў 9.6 Volts DC 200mA).

Where to put ehx microsynth in chain